Leading 10 common forklift crashes ， forklift procedure should pay attention to these matters ！.

Do not underestimate the forklift at the workplace. If the procedure is not good, there will be severe crashes in mins, and there are several crashes entailing forklifts.

Instance 1: The forklift freight blocked the vehicle driver's view, and the individual ahead can not be located, causing a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo goes beyond the allowed size of the path and hangs on the roadside shelf, which almost creates an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Situation 5: The forklift chauffeur did not discover the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift lifts the personnel unlawfully, the forklift motorist does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift rolls over.
Situation 7: The forklift driver did not put on a seat belt and fell from the lorry when it rolled over and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be risk-free prior to starting.
3. When the forklift begins with a tons, the driver must initially validate that the load is steady and trustworthy.
4. The beginning has to be slow-moving and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the pole ought to be slanted in reverse. .
2. Do not raise the fork too high when driving. When entering and leaving the job website or while driving, beware that there will be no challenges overhead. When the tons is traveling, the fork needs to not be raised too high, which will affect the stability of the forklift. .
3. After unloading, the fork needs to be reduced to the normal driving setting prior to driving. .
4. When turning, if there are pedestrians or vehicles close by, the driving signal should be released first. High-speed doglegs are banned. High-speed sharp turns will certainly cause the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the flame and slide, and it is restricted to brake suddenly while driving with tons unless there are unique circumstances.
6. When the forklift is running, it has to comply with the traffic rules in the factory and have to maintain a certain safety distance from the car in front. .
7. When the forklift is running, the tons has to remain in the lowest placement that does not hinder the driving, and the gantry ought to be appropriately tilted back. The load shall not be increased except when piling or filling. .
8. The elevation of the lots need to not obstruct the vehicle driver's sight. In special conditions, when the item influences the forward vision, drive at a reduced speed when turning around.
9. It is forbidden to activate the ramp, neither to drive throughout the ramp. .
10. The secure driving rate of the forklift in the manufacturing facility area is 5 km/h, and it has to drive safely at a reduced speed when entering the manufacturing workshop area. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to base on the fork to hold items and play a balancing function. .
12. If issues are located, they will be repaired and reported in a prompt manner, and they will certainly never operate with illnesses or conceal them.

loading and unloading.
1. When fork-loading things, the distance between both forks should be adjusted as required to make the lots of the two forks balanced and not skewed, and one side of the product ought to be against the rack. .
2. It is restricted to collaborate Electric Forklift Truck for Warehouse with a single fork or utilize a fork top or pull. In special scenarios, safety indication should be set up to remind bordering pedestrians. .
3. In the process of packing and discharging things, the forklift should be stopped with the brake. .
4. The rate of the vehicle ought to be slow-moving and steady. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled objects and injure individuals. .
5. When utilizing a fork to fork the goods, the fork ought to be as deep as possible under the tons, and it needs to be noted that the fork suggestion need to not touch other goods or items. The tons must be maintained with marginal back tilt of the gantry to make sure that the load does not slide in reverse. The mast can be tilted forward somewhat when the tons is decreased to permit simple placement of the load and removal of the forks. .
6. It is forbidden to fork goods at high speed and collide with difficult items with the fork head. .
7. When the forklift is functioning, it is forbidden for individuals to stand around the Stand-on Electric Pallet Stacker fork, so as to avoid the collapse of the goods and injure people. .
8. Overloading is prohibited, and it is banned to make use of forks to lift workers to take part in high-altitude procedures to avoid high-altitude falling crashes. .
9. It is not allowed to make use of the brake inertia to slide, place, round or roll items. .
10. It is not permitted to use forks to select, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the products on the fork impend. Before leaving the forklift, you have to unload the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is removed. (Except for unique circumstances, such as the chauffeur does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water should be included.
2. Examine the safety and security efficiency of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the car;.
2. When you run into somebody in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the incline is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the car needs to be driven backwards when worsening;.
8. When the forklift workers lug the goods and progress, if they encounter big or hefty products and most likely to the chauffeur's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to pick up the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not enabled to utilize stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Contours, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the obstacle should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844